by

Do You Want To Run This File Host Controller Driver

Save the driver file and follow the steps below to manually install the USB 3.0 driver: 1. Use Windows shortcut keys Win + X to launch the Jump List and then select Device Manager. Right click on the USB 3.0 device, for instance, Intel USB 3.0 eXtensible Host Controller. And then select Update Driver Software.

I'm trying to implement UART over a USB interface on the STM324x9I-EVAL development board. The purpose is to send commands to a servo controller (or other hardware, for that matter) serially. I've successfully implemented the USB_Device_CDC example on the development board but am unsure exactly how this works without a PC with drivers on the other end. As far as other hardware is concerned, will the USB port now simply look like a serial port? Or is there still a need for a driver or some sort of interface on the other end?

I do want to point out that I'm aware of the following post:

but I don't believe my question is fully answered within the context of that answer.

Community♦
mbanmban

2 Answers

A USB connection is not a peer-to-peer connection like a UART. It requires a host and a device in a master/slave relationship. The device cannot initiate data transfer; it must be continuously polled by the by the host.

A CDC/ACM class device presents a virtual COM port on a PC host, but that does not allow the device to communicate with a UART interface. It looks like a serial port at the software level, but does not implement a UART physical layer. There is an awful lot going on under the hood to make it look like a PC serial port, but none of it resembles UART communications at the physical level.

There are devices that act as UART/USB bridges (from FTDI and Prolific for example), and you could (somewhat expensively) build your own from a microcontroller that has a USB device controller and a UART, but the bridge is a USB device and must still connect to a USB host; these are normally used to connect a PC to a microcontroller that lacks a USB controller or where the software/CPU overhead of using a USB controller is too great.

In theory you could connect a microcontroller that has a USB host controller to one that has a USB device controller, but you need host and device software stacks on each respectively, and once you have the USB connection, implementing CDC/ACM is a somewhat inefficient use of the available bandwidth. The purpose of the CDC/ACM class is primarily to allow 'legacy' software to work on a PC.

If you need to connect to a 'real' serial port, you should use a real UART - which are far more ubiquitous than USB controllers on microcontrollers in any case.

Host
CliffordClifford

You should learn a little bit about USB device classes. CDC is a USB device class, and ACM is a subclass that I assume you are using. The device you made could be called a 'CDC ACM device' because it uses the CDC class and the ACM subclass.

These classes and subclasses are defined by the USB Implementers Forum in documents that you can find here:

These documents specify things like what USB descriptors a CDC ACM device should have in order to describe itself to the host, and what kinds of interfaces and endpoints it should have, and how serial data will be represented in terms of USB transactions and transfers.

Note that CDC ACM only specifies some USB commands for transferring data between the host and the device. It does not specify what the device will actually do with that data. You can use CDC ACM to implement a USB-to-serial adapter, or you can just use it as a general purpose communication interface for whatever data you want to send.

Yes, you do need a driver on the PC side. The driver needs to be designed to run on your specific operating system. It needs to create some kind of virtual serial port device in your operating system that other software (which only knows about serial ports) can find and connect to. It needs to translate serial port operations performed by other software on the serial port (e.g. writing some bytes to the serial port) into low-level USB commands according to the CDC ACM specifications (e.g. sending some bytes out to the device on a particular endpoint in the form of USB packets). It needs to somehow know which USB devices it should operate on, since not every USB device is a CDC ACM device.

For Windows, you will probably use the usbser.sys driver which comes with Windows. For versions of Windows older than Windows 10, you will need to write an INF file to associate your device to usbser.sys and sign it. For Windows 10 and later, there is a new INF file called usbser.inf already included with Windows which will automatically match any valid CDC ACM device. This means you don't have to write or distribute a driver for CDC ACM devices if you only intend to support using the device on Windows 10 or later. The partnership between Microsoft and Arduino which began in 2015 gives me hope that Microsoft will continue supporting and improving usbser.sys in the future. In fact, they claim that in Windows 10 'the driver has been rewritten by using the Kernel-Mode Driver Framework that improves the overall stability of the driver', so that is good news.

For Linux, there is the cdc_acm kernel module, which has been a standard part of the kernel for a long time and should work automatically with any CDC ACM device you plug in.

For Mac OS X, there is the AppleUSBCDCACM driver, which should work automatically with any CDC ACM device you plug in.

Note that for any of these drivers to recognize your device and work with it, your device has to have certain values in its USB descriptors, and the requirements can vary depending on what exact driver version you are talking about.

Will the USB port now simply look like a serial port?

No, that's the wrong way to think about it. The USB port will still look like a USB port, but the various USB drivers provided by your operating system will recognize that a CDC ACM device is plugged into that port and create a new entry in your operating system's list of serial ports. Then if you run some software that only knows about serial ports, it can connect to that port.

In fact, if you make a composite device, you can have a single USB device plugged into a single USB port that actually has two or more virtual serial ports.

David GraysonDavid Grayson
File

Not the answer you're looking for? Browse other questions tagged embeddedusbstm32uartusbserial or ask your own question.

(Debugging steps to help investigate the root-cause, not a solution)

This is for anyone who's encountering an issue with devices that don't work when plugged into a USB 3 port on a machine running Windows 8, with the symptom that the device is not functional AND the Device Manager app shows the device yellow-banged out with 'Code 43'.

Do You Want To Run This File Host Controller Driver Windows 10

The instructions below show how to capture a log file that will help diagnose this, based on the Microsoft Windows USB blog here:

  • Open an elevated command prompt window

Do You Want To Run This File Host Controller Driver Download

One way is to type 'command prompt' on the Start screen. Right-click on the Command Prompt shown in the result, and select Run as administrator.

  • Start a capture session by pasting this sequence of commands into the command prompt window:

logman create trace -n usbtrace -o %SystemRoot%Tracingusbtrace.etl -nb 128 640 -bs 128
logman update trace -n usbtrace -p Microsoft-Windows-USB-USBXHCI (Default,PartialDataBusTrace)
logman update trace -n usbtrace -p Microsoft-Windows-USB-UCX (Default,PartialDataBusTrace)
logman update trace -n usbtrace -p Microsoft-Windows-USB-USBHUB3 (Default,PartialDataBusTrace)

Do You Want To Run This File Host Controller Driver Mac

logman update trace -n usbtrace -p Microsoft-Windows-USB-USBPORT
logman update trace -n usbtrace -p Microsoft-Windows-USB-USBHUB
logman update trace -n usbtrace -p Microsoft-Windows-Kernel-IoTrace 0 2
logman start -n usbtrace

  • Perform the action that you want to capture. For example, plug in a USB flash drive that shows up as an Unknown device in Device Manager. Keep the command prompt window open.
  • Stop the session when you're finished by pasting this sequence of commands into the same command prompt window:

Do You Want To Run This File Host Controller Driver Windows 10

logman stop -n usbtrace
logman delete -n usbtrace
move /Y %SystemRoot%Tracingusbtrace_000001.etl %SystemRoot%Tracingusbtrace.etl

Do You Want To Run This File Host Controller Driver Free

  • Upload the file %SystemRoot%Tracingusbtrace.etl to SkyDrive or similar, e.g. see instructions to upload to SkyDrive here:

Do You Want To Run This File Host Controller Driver Windows 7

  • Send a link to the uploaded file.